
KETRON PEEK-1000 and TECAPEEK natural are the two names that appear most often on European drawings when the part is unfilled PEEK. They come from different producers, they carry different price tags, and engineers routinely ask which one is better. The honest answer is that the polymer is the same and the difference sits somewhere else entirely.
Both are unfilled, natural-colour PEEK made from a 450G-class resin, supplied as extruded sheet and rod. If the drawing calls for unfilled PEEK and nothing more, either will meet it. What a buyer is actually choosing between is lot consistency, the shapes that happen to be on a shelf, the documentation package, and the price of the week.
What both materials are
Strip the brand names away and the specification is identical: polyetheretherketone, unfilled, natural, semi-crystalline. The typical properties a drawing will reference are the same for both.
| Property | Typical value | What it means in practice |
|---|---|---|
| Density | 1.30 g/cm3 | Weight calculations for both |
| Tensile strength | Around 100 MPa | Ample for most structural fixtures |
| Tensile modulus | Around 3.7 GPa | Stiffer than PTFE or POM, less stiff than aluminium |
| Glass transition | 143 C | Above this, stiffness falls away quickly |
| Melting point | 343 C | Sets the ceiling for brief excursions |
| Continuous service | Up to 250 C | With adequate support and no load spikes |
| HDT at 1.8 MPa | Around 152 C | The number that limits structural use in hot air |
| Water absorption, 24 h | 0.1 to 0.3 percent | Dimensional change is real but small |
Any competent stockist will supply a data sheet with these figures. Where the two products diverge is not in the table.
Where they genuinely differ
Colour and appearance
Natural PEEK is not a fixed colour. It ranges from a pale beige to a grey-tan, and the shade shifts slightly from lot to lot because it comes from the resin and the thermal history, not from a pigment. If several parts have to look the same on a machine, order them from one lot and say so on the purchase order. This matters more than buyers expect in semiconductor and medical equipment, where a colour mismatch reads as a material mismatch to an auditor even when the properties are identical.
Lot-to-lot consistency
Both producers run tight process control, but the practical difference shows up in batch spread. A stockist who turns inventory quickly will ship you material from a recent lot; one who holds stock for years will not. Ask for the production date on the certificate, not just the certificate.
Stock shapes
This is where most projects actually decide. One brand may be available in a 12 mm sheet this week and the other only in 20 mm, or one may stock rod up to 150 mm diameter and the other stop at 100. Availability, not chemistry, drives most substitution decisions in practice.
Documentation
Both can come with a certificate of analysis. What differs is how much supporting paperwork the supplier can produce quickly: food contact statements, USP Class VI support, ISO 10993 data for a medical submission, or a declaration on residual monomer. If the application is regulated, ask for the document set before comparing prices, because the paperwork can add 15 to 30 percent and it is not included in the per-kilo figure unless you ask.
Price and lead time
The same part, in the same shape, from the two brands, typically differs by single-digit to low double-digit percentages depending on the week and the distributor. Neither brand is systematically cheaper. A quote that is dramatically lower usually reflects stock ageing, a different form, or a per-kilo figure that excludes cutting.
The substitution question, answered properly
For mechanical parts, wear parts, fixtures, insulators and machined components, substituting one brand for the other is normally acceptable, provided two things are checked: the drawing tolerances still hold in the supplied shape, and the service temperature and load case are inside the unfilled PEEK envelope. Nothing in the polymer changes.
For regulated applications, substitution is not a purchasing decision. A medical device file that references one grade has to be re-validated if the grade changes, even when the chemistry is the same, because the submission names a material and a supplier. The same applies to some aerospace and semiconductor qualification flows. In those cases the brand is part of the specification, and trying to save 12 percent on material is the wrong place to look for savings.
How to write a specification that does not lock you in
If the brand is not genuinely required, do not let it into the drawing. A specification that says unfilled natural PEEK, semi-crystalline, with a certificate of analysis and a stated lot date, gives the buyer room to take whichever brand is in stock and keeps the price competitive.
If the brand is required, say why in the notes. A line like brand specified for qualification continuity tells the supplier not to offer an equivalent, which saves a round of emails and a rejected quote.
Either way, specify the properties that actually matter to the part: tensile strength minimum, HDT minimum, filler content, colour, and the documentation set. Those five lines do more to control quality than a brand name does.
How we quote the two
When a drawing names KETRON PEEK-1000 or TECAPEEK natural, Top Plastic quotes against that name if the qualification genuinely requires it, and against an equivalent unfilled PEEK when it does not, stating clearly which one is being offered and what is on the shelf. Where both brands are available, both prices are given with their lead times, so the comparison is between two real offers rather than two list prices.
If you are working through a substitution and need the property comparison in writing for a qualification file, send the drawing and the current material certificate. Details of the unfilled and filled grades are on the PEEK material page.
Need a material recommendation?
Send us the application and we will reply with two or three candidate grades and a price.
