
Buyers often treat POM sheet and POM rod as the same material in two shapes, and ask us to price whichever costs less per finished part. Most of the time that works. But acetal extrudes under tension, and the extrusion direction locks a grain into the stock — a preferred orientation of the polymer chains that makes the material measurably different along the flow direction than across it. Sheet and rod are extruded along different axes, so the grain sits in different places relative to your part, and that is where the two stock forms stop being interchangeable.
Where the grain lives
In extruded sheet, the polymer flows horizontally as the sheet leaves the die. The chains align along that flow, so the stock carries its strongest directional properties along the length of the sheet and its highest shrinkage tendency in the same direction. Across the width and through the thickness, orientation is progressively lower.
In extruded rod, the flow runs along the bar axis. The grain wraps around the circumference: identical in every radial direction, different along the axis. That symmetry is why rod behaves so consistently for turned parts — every point on the cross-section has the same history.
| Stock form | Grain direction | What it affects |
|---|---|---|
| Sheet | along the extrusion length | flatness, linear shrinkage, bending stiffness by direction |
| Rod | around the circumference, along the axis | ovality after boring, axial vs radial dimension drift |
What it does to machined parts from sheet
Machine a plate part from POM sheet and the grain decides how it moves. Removing material unbalances the locked-in stress: the part relaxes toward the direction with higher orientation, and a long feature along the extrusion direction bows more than the same feature across it. The classic failure is a bracket or plate milled with one long axis: it comes off the machine flat, and is out of flat a day later, curved along the extrusion direction.
Three habits control it:
- Orient the part on the sheet deliberately. If a long feature must stay flat, run it across the grain, not with it, or accept a stress-relief cycle in the plan.
- Balanced roughing. Remove stock equally from both faces before finishing. One-sided machining of sheet is the single most common cause of bowing in acetal.
- Anneal at the right point. Stress relief around 120–140 °C with slow cooling, between roughing and finishing, lets the part settle before the dimensions that matter are cut.
What it does to turned parts from rod
Rod’s circumferential grain is friendly to turning but has one trap: boring. When you bore deep into the bar, you remove the compressed outer layers and expose the core, which carries a different stress state. The bore can close in slightly over hours to days — more on large-diameter bar, more in homopolymer, and more the deeper the bore relative to wall thickness.
The shop-level answers are the same family as for sheet: rough the bore oversize, let the part rest or anneal, finish the bore last. For precision bores in POM, finish machining on a different day than roughing is not perfectionism — it is how the tolerance survives to inspection.
Which stock form for which part
- Thin, flat, wide parts (gaskets, wear strips, insulating plates): sheet, cut across the grain where stiffness matters, or accept the flatness cycle.
- Round parts (bushings, rollers, seals, spacers): rod, always — a disc cut from sheet carries the sheet grain into a circular part and the ovality drifts.
- Blocky parts (gears, cams, housings): whichever nests better; but gears cut from sheet can develop tooth-to-tooth inconsistency as the grain crosses the profile, which is why gear blanks usually come from rod.
- Long thin parts (rails, slides): sheet along the length gives consistent cross-section and better yield from stock; mind the bow with balanced machining.
Does the grade matter here?
Yes, in degree. Copolymer relaxes less dramatically than homopolymer because its crystallinity is lower, so sheet bowing and bore closure are both milder in POM-C than POM-H. Neither escapes the physics — the grain is an extrusion consequence, not a brand choice — but if a drawing sits right at the edge of flatness tolerance, the copolymer gives you margin for free.
Questions we field weekly
Can I buy thick sheet instead of rod to save material? For round parts, usually no: the disc you cut carries grain that a rod blank does not, and the drift shows up as ovality. For blocky parts, thick sheet often wins on yield.
How long should parts rest before finish machining? Overnight minimum after heavy roughing; 24 hours is the practical standard for precision bores and flat parts.
Does annealing change the dimensions? Slightly — expect a few tenths per hundred millimetres of shrink toward the grain direction. That is exactly why finish dimensions come after anneal, not before.
Is this different for cast or moulded stock? Compression-moulded and cast stock have far lower orientation; the discussion mostly applies to extruded sheet and rod, which is what the market stocks.
Top Plastic stocks POM-C and POM-H in sheet, rod and tube, offers sawn blanks stress-relieved before shipment, and machines parts to drawing with the grain direction chosen deliberately. Send the part and its tolerance targets, and we will propose the stock form, the machining sequence and, where it matters, the annealing points.
Need a material recommendation?
Send us the application and we will reply with two or three candidate grades and a price.
