Mon–Sat 08:30–18:00 (GMT+8) Founded 2009 Dongguan, China

PEEK tube and hollow bar: when machining from tube beats rod

PEEK tube costs more per kilogram than rod and still saves money on most ring-shaped parts. The arithmetic is simple; the constraints are not.

Material Selection 7 min read
PEEK tube and hollow bar: when machining from tube beats rod

A ring-shaped part is the most common geometry in PEEK machining, and the most expensive way to make one is to buy a solid rod and turn most of it into chips. On a 120 mm outside diameter bushing with a 90 mm bore, a solid starting blank at 130 mm weighs about two and a half times the finished part. Everything else leaves as swarf, and PEEK swarf has no scrap value worth counting.

Tube solves the material problem and introduces three new ones: wall thickness range, concentricity, and ovality that shows up the moment you chuck a thin wall. This article sets out the arithmetic, the limits, and the cases where rod is still the right purchase.

The arithmetic of a ring

The mass you buy is proportional to the cross-section you start with, not to the part you finish.

Starting stock Cross-section, mm2 Relative material bought Material leaving as swarf
Rod 130 mm 13,273 2.68 about 63 percent
Tube 120 / 90 mm 4,948 1.00 5 to 15 percent for finishing
Tube 125 / 85 mm with boring allowance 6,362 1.29 about 22 percent

For a part that finishes at 120 / 90 mm and 50 mm long, rod costs roughly 2.7 times the material of tube and leaves about 4 kg of chips on the floor. At current PEEK prices that difference is not a rounding error, it is usually larger than the entire machining cost of the part.

Tube, however, does not cost the same per kilogram as rod. It is extruded over a mandrel or bored from a pressed billet, it is made in fewer sizes, and the mill charges for the operation. The premium is typically 10 to 25 percent per kilogram over comparable rod. The calculation that matters is the product of mass and price:

  • Rod: mass index 2.68, price index 1.00, cost index 2.68
  • Tube at a 20 percent premium: mass index 1.00, price index 1.20, cost index 1.20

Tube wins by more than half on material cost. It only loses that advantage when the tube size you need does not exist and you buy the next size up with a thick wall, or when the wall is so thin that scrap rates erase the saving.

Where tube is the obvious purchase

The geometry that pays for tube is a part where the bore is concentric with the outside and the wall is a meaningful fraction of the diameter.

  • Bushings and sleeve bearings. The classic case, especially above 60 mm outside diameter where rod removal becomes brutal.
  • Seal housings and gland rings. Concentric by function, so the tube’s own concentricity is not a liability.
  • Insulating sleeves and standoff tubes. Long, thin, and often needed in quantity.
  • Rollers and guide rings. Where the wall carries the load and the bore is only a mounting feature.

A practical trigger: when the bore is more than about half the outside diameter and the part is longer than it is deep, price the tube before the rod. On a 50 mm long part with a 90 mm bore, tube is not a marginal improvement, it is a different cost structure.

Where rod still wins

Tube is a constrained shape, and the constraints are the reason rod keeps a large share of the business.

Off-centre features. A bushing with a keyway, a flange, an eccentric bore, or a cross-hole that breaks the wall cannot come out of a tube whose wall is already the finished thickness. It needs stock around the feature.

Thin walls. Stocked PEEK tube usually runs from about 5 mm wall upward, with some sizes down to 3 mm. Below that the tube is oval, the wall varies around the circumference, and holding a concentricity tolerance after machining becomes a fight. A 2 mm wall sleeve is normally machined from rod or from a thicker tube, not bought as thin-wall tube.

Small quantities and odd sizes. Tube exists in a catalogue of standard outside and inside diameters. If the part falls between two sizes, buying the next wall up throws away much of the saving, and buying rod is simpler.

Tight concentricity from a single setup. Extruded tube carries wall eccentricity, which is fine when both surfaces are machined, and a problem when the bore is used as supplied.

Wall variation and the ovality trap

An extruded PEEK tube is not a machined ring. Wall thickness typically varies by a few tenths of a millimetre around the circumference, and the tube can be slightly oval, especially at the ends. If both the bore and the outside are machined, that variation is absorbed by the cut. If the bore is used as supplied and only the outside is turned, the finished wall inherits the eccentricity, and a wall that is 8 mm on one side and 7.5 mm on the other is a balancing and sealing problem.

The second trap is chucking. A tube with a 10 mm wall in a three-jaw chuck at 100 mm diameter deforms under the jaw load, springs back when released, and produces a bore that is round in the machine and out of round on the bench. Pie jaws, an expanding mandrel, or turning between centres with soft plugs solve it; a standard chuck does not.

Residual stress in tube, and the slit test

Tube carries its own stress pattern. Extrusion orientates the material along the axis, boring a pressed billet releases stress unevenly through the wall, and the result is a ring that moves when it is parted off. A quick check before committing to a batch: part off a thin ring, slit it radially, and measure how much the gap opens. A gap of a few tenths of a millimetre on a 100 mm ring is normal; a gap of several millimetres means the tube needs annealing before any precision work.

For parts with a wall under about 15 percent of the diameter, or with a sealing face, specify annealed tube. The anneal is done by the supplier at the semi-finished stage, and it is cheaper than discovering the movement after the finish bore.

Machining sequence for a tube part

The order of operations matters more with tube than with rod, because the part is flexible for most of the process.

  • Face and rough the bore first, holding on the outside with pie jaws. Roughing while the wall is still thick keeps the deflection down.
  • Leave the finish bore for after the outside is turned, so the last cut is made on a part that is already round on its mounting surface.
  • Part off with a sharp tool and low feed, and support the free end. A parting tool pushing into a thin wall closes the bore behind the tool and pinches it.
  • Deburr before measuring. A rolled-over edge on a PEEK tube reads as a size error on a micrometre.
  • Check roundness after release, not in the chuck. Every tube part is round while it is clamped.

What to put on the purchase order

Five lines prevent most tube problems. Outside diameter and tolerance. Inside diameter and tolerance, plus whether the bore may be used as supplied. Wall thickness minimum, stated separately, because OD and ID tolerances can combine to violate a wall you never specified. Length and cut tolerance. And the stress relief state: as extruded, or annealed.

If the bore is as-supplied, also state the concentricity or wall uniformity you need. It is a separate property from diameter tolerance and it is the one that causes arguments.

Questions we get about PEEK tube

Is tube cheaper than rod per kilogram? No, usually 10 to 25 percent more. It is cheaper per finished part, which is the number that matters.

What is the largest PEEK tube you supply? Outside diameters up to about 300 mm in standard extrusion, larger on request; wall thickness from about 5 mm to 40 mm in stocked sizes.

Can I use tube for a part with a flange? Only if the flange diameter is larger than the tube outside diameter, which means you are back to buying material around it. For flanged parts, rod or a near-net shape is usually cheaper overall.

Does tube machine differently from rod? The cutting parameters are the same. The workholding is not, and that is where most tube parts go wrong.

Top Plastic supplies PEEK tube and hollow bar from 20 mm to 300 mm outside diameter in unfilled, glass filled, carbon filled and bearing grades, with annealed options and cutting to length. Send the drawing with the bore and wall dimensions and we will price both the tube route and the rod route, so the comparison is on finished-part cost rather than on list price.

Need a material recommendation?

Send us the application and we will reply with two or three candidate grades and a price.

Ask an engineer
Share this article

Send us your drawing, get a price in 24 hours

Tell us the material, the size and how many pieces. If you are not sure about the material, describe the application and we will recommend one.

Request a quote Browse stock shapes