Mon–Sat 08:30–18:00 (GMT+8) Founded 2009 Dongguan, China

Why 1 mm PEEK sheet costs more per kilogram than 50 mm

The thinnest gauge usually carries the highest per-kilo figure. Here is the arithmetic behind that gap, and how to buy thin PEEK without paying for material that never ships.

Material Selection 7 min read
Why 1 mm PEEK sheet costs more per kilogram than 50 mm

Ask for a price on PEEK sheet and the thinnest gauge usually carries the highest per-kilogram figure. A 1 mm sheet in the same grade, from the same producer, in the same order, can quote 30 to 60 percent above a 50 mm block. Buyers read that as a pricing trick. It is not. A kilogram of 1 mm PEEK sheet is a different product from a kilogram of 50 mm block, and most of the gap is material that never reaches the customer.

This article shows where that material goes, which of the five cost drivers actually move the number, and how a buyer can specify thin sheet so the quote stops paying for scrap.

Start with the weight, because the weight is the surprise

PEEK has a density of about 1.30 g/cm3. A 1 mm sheet at 1000 by 2000 mm weighs roughly 2.6 kg. A 50 mm block at the same footprint weighs about 130 kg. That single fact reorganises the whole transaction: to buy 50 kg of 1 mm sheet you need about 19 sheets, and every one of them has to be extruded, trimmed, checked for thickness and kept flat. To buy 50 kg of block you need a piece less than half a metre square, sawn from one billet.

Nineteen thin sheets carry nineteen times the handling events, nineteen times the edge trim length and nineteen times the chance of a flatness complaint. None of that appears on a per-kilo line, yet all of it is inside the price.

Driver one: line speed and cycle time

Thin gauge runs slower, not faster. An extrusion line producing 1 mm sheet has to hold thickness across a two-metre width while the material cools within seconds of leaving the die. Line speed is limited by the cooling length available, and the tolerance band is tighter in absolute terms: plus or minus 0.05 mm on a 1 mm sheet is a five percent variation, while the same absolute band on a 50 mm block is one tenth of one percent.

Compression moulded block works the other way. A thick block occupies the press for hours, which is why 50 mm block is not the cheapest form per kilo either, but the labour attached to that cycle is spread over 130 kg instead of 2.6 kg.

Driver two: trim and edge loss

Every sheet is produced oversized and trimmed to final dimension. On a 50 mm block the trimmed edge is a few percent of the mass. On a 1 mm sheet the same 20 to 30 mm edge allowance is a much larger share of a 2.6 kg piece, and the trimmed strip has almost no resale value as virgin material.

Add start-up and shut-down scrap. A thin line needs several metres of stable gauge before the sheet is saleable, and that ramp-up material is generated per run. Order 19 sheets as one run and the ramp-up is amortised across all of them; order two sheets at a time and the buyer pays the ramp-up four times over.

Driver three: flatness, stress and secondary operations

Thin PEEK sheet warps. The material leaves the die with orientation and internal stress, and at 1 mm there is very little section to resist it. Producers therefore anneal and often press-flatten thin gauge, which is a second thermal cycle, a second handling step and a second chance to scrap a sheet.

This is also why thin sheet is usually supplied in a wider tolerance on flatness than block, and why a buyer who specifies 0.1 mm flatness over a one-metre sheet should expect a visible premium rather than a standard line item.

Driver four: inspection density

Quality control is charged per piece, not per kilogram. A 130 kg block gets one thickness check, one ultrasonic scan and one dimensional report. Nineteen 2.6 kg sheets get nineteen of each. On thin gauge the ultrasonic check also matters more, because a void or a gel spot that would be machined away inside a block becomes a through defect in a 1 mm sheet.

Driver five: packing and volumetric freight

Thin sheet is packed flat, in wooden cases, often with interleaving to stop abrasion. It is light and bulky, so freight is charged on volume rather than weight, and the crate itself can approach the value of the material inside it. Block is dense and stacks well. Two shipments of the same value can differ by a factor of three on freight alone.

The five drivers, as a table

Gauge Relative price per kg What dominates the number
1 mm 1.35 to 1.60 Trim loss, flatness control, inspection per piece, volumetric freight
3 mm 1.10 to 1.20 Still trim-sensitive, but flatness is easier to hold
6 to 25 mm 1.00, the reference Best yield per hour on continuous extrusion
50 mm block 1.05 to 1.15 Long press cycle, but the cycle cost is spread over high mass
100 mm block 1.20 to 1.35 Cooling control to avoid voids, more machining to reach a sound core

The multipliers are indicative for unfilled virgin PEEK and move with the fibre and energy markets, but the ordering holds across grades. A carbon filled 1 mm sheet is dearer than a carbon filled 50 mm block for exactly the same reasons.

The number buyers should compare instead

Per-kilo pricing rewards the wrong decision when the part is small. Take a 1 mm sheet used for a 60 by 40 mm insulation washer. A 1000 by 2000 mm sheet yields over 800 blanks. At a 1.5 multiplier the material cost per blank is a few cents, and the machining, packing and freight per blank dominate the part cost entirely.

For thin gauge, compare price per part or price per square metre of usable area, not price per kilo. Ask the supplier for the yield on your cut pattern. A quote that is 40 percent higher per kilo but supplies a wider sheet with less edge trim can be the cheaper quote per finished part.

How to buy thin PEEK without paying for scrap

  • Order full sheets, not cut blanks. Cutting is a service, and a supplier who cuts 40 small pieces from a sheet charges for the offcuts he cannot sell.
  • Consolidate gauges into one order. Two or three thicknesses placed together amortise the ramp-up scrap and the freight crate across the whole shipment.
  • Specify commercial tolerance unless the part demands otherwise. Plus or minus 0.1 mm on 1 mm sheet is a normal commercial band; asking for plus or minus 0.02 mm converts a stock item into a special.
  • Ask what the trim allowance is and whether it is inside the quoted dimension. A 1000 mm wide sheet quoted as 1000 mm usable is a different value from one quoted at 1000 mm gross.
  • Buy three to six months at a time. Thin sheet stores flat and does not degrade, and the volume break usually beats the carrying cost.

When the per-kilo comparison is simply the wrong tool

Comparing sheet against rod, or tube against block, on a per-kilo basis produces conclusions that do not survive contact with a machining drawing. Rod is bought to be turned down, so the buyer pays for the core that becomes swarf. Tube is bought to avoid that swarf. The correct comparison is cost per finished part including machining time, and per-kilo pricing only becomes useful once the form is fixed.

Questions that come up in every thin sheet quotation

Is 1 mm PEEK sheet extruded or pressed? Both routes exist. Continuous extrusion with calendering is the usual route for 1 mm and below; some producers press thin sheet in a multi-daylight press. The route affects flatness and surface, not the polymer.

Can I buy 0.5 mm? Usually yes, but as roll or press-formed sheet with a high minimum quantity, and with a wider thickness tolerance. Below 0.5 mm the material behaves more like film and the flatness conversation changes completely.

Does thin sheet cost more because it is a special? Only when it is not stocked. A standard 1 mm gauge held in inventory carries the normal premium described above; a non-standard width or a precision thickness adds a separate set-up charge on top.

Top Plastic holds unfilled, glass filled, carbon filled and ESD PEEK sheet from 1 mm to 100 mm and quotes thin gauge per part as well as per kilo, so the comparison lands on the number that matters. Send the drawing and the annual quantity and we will return both figures.

Need a material recommendation?

Send us the application and we will reply with two or three candidate grades and a price.

Ask an engineer
Share this article

Send us your drawing, get a price in 24 hours

Tell us the material, the size and how many pieces. If you are not sure about the material, describe the application and we will recommend one.

Request a quote Browse stock shapes