Mon–Sat 08:30–18:00 (GMT+8) Founded 2009 Dongguan, China

PEEK price per kg in 2026: the five factors behind the number

A PEEK price per kg is not a market rate. It is the output of five decisions, and knowing which one moved explains most quote gaps before you argue about them.

Material Selection 10 min read
PEEK price per kg in 2026: the five factors behind the number

Every PEEK quotation ends in one number: price per kilogram. Buyers treat that number as a market rate and compare it across three suppliers as if PEEK were traded like copper. It is not. The per-kilo figure is an output of five decisions, and when two suppliers quote the same grade at 80 and at 130, both are usually right. They are answering different questions.

This article breaks the number into the five factors that actually build it, with the multiplier each one adds, so a buyer can see where a gap comes from instead of negotiating blind.

Baseline: what a per-kilo figure can and cannot mean

Start with a reference point. In early 2026, unfilled virgin PEEK sheet in lots of 20 to 50 kg typically quotes somewhere between 70 and 120 US dollars per kilogram ex-works, depending on thickness and quantity. That band is wide on purpose: it is not a price, it is the range in which the first four factors have not yet been fixed. Once grade, form, quantity and documentation are specified, the band collapses to a few dollars.

Treat any quote below the bottom of that band as a question, not a bargain. It usually means regrind, a different grade, or a per-kilo figure that excludes cutting and freight.

Factor one: the grade, and what has been added to it

Unfilled PEEK is the cheapest thing the material can be. Everything else is a compound, and compounds carry both a material cost and a processing cost.

Grade Relative to unfilled virgin Why the number moves
Virgin unfilled 1.00 Baseline
30 percent glass fibre 1.10 to 1.25 Glass is cheaper than polymer, but compounding adds a melt step and wear on tooling
30 percent carbon fibre 1.55 to 1.90 Carbon fibre itself is the cost driver, not the compounding
Bearing grade (carbon, PTFE, graphite) 1.70 to 2.10 Three components, tighter dispersion control, more scrap at start-up
ESD and conductive 1.30 to 1.60 Carbon loading plus a resistivity test on every batch
Implantable or medical Plus 15 to 30 percent Dedicated lines, lot testing, documentation that has to be generated and kept

The multipliers are indicative and move with the fibre market, but the ordering does not change. A buyer comparing a carbon filled quote against an unfilled quote is not comparing suppliers, he is comparing two different materials.

Factor two: form and thickness

The same compound in a different shape has a different price per kilo, because yield and cycle time change.

  • Sheet from 6 to 25 mm is the most efficient form to produce: continuous extrusion, low scrap, fast cooling. This is where the lowest per-kilo figures sit.
  • Thin sheet below 3 mm costs more per kilo, not less. Handling losses, edge trim and slower line speeds mean a smaller share of the input material ends up in the shipped sheet.
  • Thick block above 50 mm costs more per kilo because the cycle time is long and the cooling has to be controlled to avoid voids. A press cycle can occupy the equipment for hours.
  • Rod usually sits between the two for small diameters, but large diameter rod is often dearer than sheet per kilo, because the outer material has to be machined away to reach a sound core.

This is why a buyer who asks for a price per kilo without naming the form often gets the sheet figure and then a surprise when the order is for rod or block.

Factor three: quantity and cut pattern

PEEK is produced in runs, not continuously. A 20 kg order and a 500 kg order are different transactions with different economics.

In practice the curve looks like this: from 10 kg to 100 kg the per-kilo figure typically falls 10 to 15 percent; from 100 kg to 500 kg it falls another 8 to 12 percent; beyond that the curve flattens, because the material cost now dominates and the setup is fully amortised. The exact percentages depend on whether the supplier is shipping from stock or scheduling a run.

The cut pattern matters as much as the tonnage. A buyer who needs 200 pieces of 180 by 220 mm from a 1000 by 2000 mm sheet will use 83 percent of it with good nesting and 60 percent with a careless one, and the per-kilo price of the finished parts differs by a third even though the sheet price did not change. Sending a nesting drawing is the cheapest negotiating move available.

Factor four: documentation and traceability

Paper is a real cost line in engineering plastics, and it is the one buyers most often forget to specify.

  • Certificate of analysis tied to the production lot: standard for stock sales, small cost.
  • Full lot traceability from resin batch to shipped sheet: adds administrative time, occasionally forces the supplier to hold dedicated stock.
  • Food contact statements and migration testing: a one-off cost per grade, but it has to exist before the order.
  • ISO 10993 biocompatibility for medical projects: expensive to generate and expensive to keep current, and usually the reason a medical quote is 15 to 30 percent above an industrial quote for the same polymer.

If the drawing does not need the paperwork, say so explicitly. Suppliers add documentation defensively when an enquiry is silent, because sending an unqualified sheet into a regulated application is a risk they cannot take.

Factor five: logistics, Incoterms and currency

PEEK is a low-volume, high-value material, so freight is a small share of the number, but it is not zero and it is where quotes become incomparable. Ex-works, FOB and delivered prices for the same sheet can differ by 4 to 8 percent, and a delivered price that includes duties and clearance is not the same product as an ex-works price.

Currency adds a second layer. PEEK resin is priced internationally, so a supplier quoting in euros carries exchange risk between quotation and shipment, and quotes are usually held for 15 to 30 days rather than 90.

How to compare two quotes without arguing

The fastest way to close a quote gap is to convert both to the same basis.

  1. Price per finished part, not per kilo. That includes the machining allowance, the saw kerf and the scrap.
  2. The same grade, named by filler content, not just by a brand or a colour.
  3. The same form and thickness, with tolerance class stated.
  4. The same Incoterm and the same validity period.
  5. The same documentation package.

Do that and a 60 percent gap usually becomes a 10 percent gap, or it turns out that one quote was for regrind and the other for virgin material.

What is moving the number in 2026

Three things are worth watching this year. Energy costs in the producing regions push the extrusion and annealing steps, which are the energy-intensive parts of the chain. Capacity for high-performance polymers is being added, which caps how far prices can rise. And freight rates on the Asia to Europe lane have been volatile enough that delivered quotes now carry shorter validity than they did three years ago.

None of these changes the structure of a quote. They change the level of it.

Getting a number that holds

Send the grade by filler type and percentage, the form and thickness with tolerance, the quantity in both sheets and finished parts, the cut pattern if there is one, the documentation you actually need, and the destination and Incoterm. With those seven lines a supplier can quote firmly instead of quoting a range and revising it after the order.

Top Plastic quotes PEEK sheet and rod against the stocked thickness bands, so the per-kilo figure comes with a stated lead time rather than a scheduled run. Current grades and forms are on the PEEK material page. If you are still choosing between filled grades, the comparison of GF30, CA30 and bearing grades answers the selection question before the commercial one.

Need a material recommendation?

Send us the application and we will reply with two or three candidate grades and a price.

Ask an engineer
Share this article

Send us your drawing, get a price in 24 hours

Tell us the material, the size and how many pieces. If you are not sure about the material, describe the application and we will recommend one.

Request a quote Browse stock shapes