
Three filled PEEK grades appear on most enquiries: 30 percent glass, 30 percent carbon, and a bearing grade carrying carbon, PTFE and graphite. Buyers often treat them as a ladder, assuming the bearing grade is the best and GF30 the entry level. They are not a ladder. They answer three different questions, and picking the wrong one produces a part that either wears out early or wears out the steel it runs against.
This guide fixes the choice on four inputs a designer already has: load, sliding speed, counterface material and whether the part must conduct. It then covers how each grade behaves on a machine tool, because the machining cost of filled PEEK is part of the selection.
What each fill actually does
Neat PEEK is already a capable wear material. It has a low friction coefficient for an unfilled thermoplastic, good creep resistance at temperature, and it holds dimensions. Fillers are added to push one specific property, and each push costs something elsewhere.
| Grade family | What is in it | What it gains | What it gives up |
|---|---|---|---|
| GF30 | 30 percent glass fibre | Stiffness, creep resistance under sustained load, dimensional stability, lower cost per kilo | Wear against hard counterfaces, elongation, impact, tool life |
| CA30 | 30 percent carbon fibre | Stiffness, strength, thermal conductivity, electrical conductivity, low expansion | Cost, wear of soft or dissimilar metals, galvanic risk in wet service |
| Bearing grade | Carbon fibre plus PTFE and graphite | Lowest friction coefficient, best dry-running behaviour, self-lubrication | Strength and creep resistance versus CA30, higher cost, lower limiting PV |
The numbers matter less than the ordering. GF30 is the structural option. CA30 is the strong, conductive and thermally stable option. Bearing grade is the low-friction option. Load capacity runs GF30 and CA30 above bearing grade; friction runs the other way.
GF30: the structural choice, with a wear caveat
Glass fibre raises the tensile modulus of PEEK from roughly 3.7 GPa to about 11 GPa and cuts creep under a sustained load by a factor of two to three at elevated temperature. That is what a pump housing, a valve seat carrier or a support block needs: a part that does not slowly change shape under a constant load at 150 C.
The caveat is the fibre itself. Glass is harder than most stainless steels and considerably harder than aluminium or brass. A glass filled surface running against a soft metal polishes it away, and the embedded fibre acts like a fine abrasive. In a dry sliding contact against stainless steel, GF30 can wear the shaft faster than neat PEEK would.
Use GF30 where the load is mostly static or where the counterface is hardened and ground, and where the part is a structure rather than a sliding surface. It is also the cheapest of the three, which makes it the default in cost-driven designs, sometimes wrongly.
CA30: stiffness plus conductivity, and a different wear signature
Carbon fibre takes the modulus higher than glass, to around 13 to 15 GPa, and adds two properties glass cannot: thermal conductivity roughly three times that of neat PEEK, and enough electrical conductivity to dissipate static. In a dry running bearing, that thermal conductivity is worth more than the extra stiffness, because the heat generated at the contact patch has somewhere to go.
The wear signature differs from glass. Carbon fibre is softer than glass and, in dry contact against hardened steel, it can form a transfer film that lowers friction over time. Against aluminium, magnesium or soft bronze it can still abrade, and in wet service carbon against steel introduces a galvanic couple. In seawater or in a coolant-flooded bearing, that matters.
CA30 is the right default for a wear part that has to carry load, run dry, and stay dimensionally stable, particularly when the part also needs to be static dissipative. It is the most expensive of the three by a wide margin, often 1.6 to 1.9 times unfilled.
Bearing grade: the lowest friction, within a load ceiling
A bearing grade adds PTFE and graphite to a carbon filled base. PTFE lowers the friction coefficient at the sliding interface and graphite supplies lubrication where the PTFE film breaks down. The result is a material that runs dry at a friction coefficient around half that of neat PEEK, with far less stick-slip at low speed.
The trade is mechanical. PTFE is soft and does not carry load, so the compressive strength and creep resistance fall below CA30. The limiting pressure-velocity product is also lower, which means the grade that is best at low speed and moderate load is the wrong grade for a high-load, high-speed application where CA30 would survive.
Bearing grade is the correct answer for thrust washers, slide pads, bushings in dry reciprocating motion, and anywhere the failure mode is squeal or stick-slip rather than bulk deformation. It is the wrong answer for a structural bracket with a sliding face, where the two requirements should be split into two materials.
The four questions that decide it
One: is the load sustained and structural, or is it a contact load? Sustained structural load points to GF30 or CA30. Contact load with sliding points to bearing grade.
Two: what is the counterface, and how hard is it? Hardened and ground steel tolerates all three. Aluminium, brass and soft stainless rule out glass and penalise carbon.
Three: what is the sliding speed and the PV product? Above roughly 0.5 MPa·m/s dry, bearing grade runs out of headroom and CA30 takes over. Below it, bearing grade wins on friction and noise.
Four: does the part need to conduct, or must it insulate? Static dissipation is a CA30 or ESD grade requirement. Electrical insulation excludes carbon entirely, which leaves GF30.
| Application | First choice | Reason |
|---|---|---|
| Pump wear ring, dry, hardened shaft | Bearing grade | Low friction at the running clearance, no stick-slip at start-up |
| Thrust washer, reciprocating, low speed | Bearing grade | Dry lubrication, quiet running |
| Gear pair running dry at temperature | CA30 | Load capacity plus heat removal through the fibre |
| Valve seat carrier, static load at 180 C | GF30 | Creep resistance per unit cost |
| Bushing on an aluminium shaft | Neat or bearing grade | Neither glass nor carbon should touch soft metal |
| Static dissipative guide rail | CA30 or ESD grade | Conductivity requirement overrides wear ranking |
What each grade does to the machine shop
Filled PEEK machines differently from neat, and the difference shows up in the quote.
- Tool wear. GF30 is the most abrasive. Carbide tools lose edge quickly and a production run may need twice the tool changes of neat PEEK. Diamond coated tooling pays back on volume above a few hundred parts.
- Dust. Carbon filled dust is electrically conductive. It must be extracted at the cut, not blown with compressed air, or it will migrate into cabinets and across insulation.
- Annealing. All three grades benefit from a post-machining anneal, but thick sections in GF30 and CA30 need a slower ramp, because the fibre network reduces the rate at which stress can relax.
- Threads and thin walls. Glass filled material chips at thread crests and splits at thin wall sections. Design with a larger root radius, and prefer inserts where the thread will be assembled more than a few times.
- Edge finish. Bearing grade cuts cleanly and takes a fine finish; glass filled tends to fuzz at a sawn edge and needs a finishing pass.
Questions that come up at the quotation stage
Is GF30 stronger than CA30? Not in tension. Carbon gives higher strength and higher modulus. Glass wins on cost and on compressive creep in some configurations, which is why it survives in structural parts.
Can a bearing grade run in water? It can, but the advantage narrows, because water already provides a lubricating film. In wet service the choice usually moves to CA30 on strength, or to neat PEEK on cost.
Are filled grades food contact approved? Some are, some are not, and the answer depends on the specific filler and the specific approval. Do not assume that a base PEEK approval carries over to a compound; ask for the compound certificate.
Can I mix requirements in one part? Often yes in geometry, rarely in material. A structural body with a sliding face is usually two parts, one GF30 or CA30 and one bearing grade, which is cheaper than compromising on a single grade and replacing it twice a year.
Top Plastic stocks GF30, CA30 and bearing grade PEEK in sheet and rod, and will machine a trial part from two grades so the wear decision is made on test data rather than on a datasheet. Send the load, speed and counterface and we will recommend a starting grade with the reasoning.
Need a material recommendation?
Send us the application and we will reply with two or three candidate grades and a price.
