Пн–Сб 08:30–18:00 (GMT+8) Основана в 2009 году Дунгуань, Китай

Tube and hollow bar in engineering plastics: a size guide

Wall thickness, ovality and concentricity drive the cost and capability of plastic tube. Which grades come as tube, and when hollow bar wins on cost.

Поставка
PTFE Virgin Sheet, Rod and Tube

Ordering plastic tube hollow bar instead of solid rod is often the fastest route to a bushing, an insulator or a wear ring, because the bore is already there. Tube arrives closer to the finished shape, so you remove less material and generate less swarf, but you also take on the mill’s tolerances for wall thickness, ovality and concentricity. Getting those three numbers right is what separates a tube order that machines cleanly from one that has to be re-bored before it can be used.

This guide covers which engineering plastics are supplied as tube, the wall and concentricity tolerances that are realistic, and when hollow bar beats both tube and solid rod on cost. It assumes you are buying from stock and either machining the final part yourself or having it machined to order.

What comes as tube and what does not

Not every engineering plastic is produced as tube. PTFE, PVDF, PEEK, PPS, POM and PA66 are all commonly available as tube or hollow bar across a range of outside diameters, because they extrude or compression mould well in that form. Some filled grades are harder to run as thin-wall tube, and very small inside diameters combined with long lengths are difficult to keep concentric. In our experience it is worth asking what the mill actually stocks rather than designing around a catalogue that is theoretical. Where a specific grade is not made as tube, a thick-wall hollow bar or a part machined from rod is usually the practical answer, and it helps to know which of those the supplier holds on the shelf.

Wall thickness, ovality and concentricity tolerance

Three dimensions define a tube order, and they are not interchangeable. Wall thickness sets the stiffness and the bore you can reach; ovality is how far the outside diameter departs from round; concentricity is how well the inside and outside diameters share a centre. The dimensions you state when you order plastic tube hollow bar decide whether the parts machine cleanly. As a rule of thumb, extruded plastic tube holds ovality and concentricity on the order of a few per cent of the diameter, and tighter than that is a machining operation rather than an extrusion one. Thin walls are harder to hold than thick ones, and the ratio of wall thickness to diameter matters more than either figure on its own. State all three on the enquiry, with the length, because a tube that meets the outside diameter and misses the wall is still scrap.

Virgin PTFE sheet, rod and tube. PTFE tube and hollow bar

Machining from tube versus boring from rod

Tube and rod solve different problems. Boring a bushing from solid PEEK rod gives you full control of the bore and the outside diameter in your own shop, at the cost of removing a lot of material and generating a lot of swarf, which is expensive in grades such as PEEK and PTFE. Starting from tube leaves less to remove, so cycle time and material waste fall, but you inherit the mill’s concentricity and may have to take a cleanup cut to true the bore up. For a short run of parts with a tight bore, rod is often simpler; for a long run or an expensive grade, tube pays for itself quickly.

PEEK natural sheet and rod stock shapes. PEEK rod stock for boring bushings

Cost comparison: tube, hollow bar and solid rod

Cost per part, not cost per kilo, decides between the three. Solid rod is the most expensive per part because you pay for material that ends up as swarf. Tube is cheaper per part when the bore you need already exists, and hollow bar sits between the two, giving a smaller bore and a thicker wall than standard tube. The choice between plastic tube hollow bar and solid rod is therefore a cost-per-part question rather than a price-per-kilo one, and our cut-to-size service will quote all three forms on the same enquiry.

Form Material removed Best when Relative cost per part
Solid rod Высокая Short runs and tight bores Highest
Hollow bar Средняя Small bore, thick wall, one-off parts Средняя
Extruded tube Низкая Long runs, standard bore, thin wall Lowest
Cast tube Низкая Large diameters with a thick wall Medium to high

Applications: bushings, insulators, sight glasses

Most tube orders fall into a few families. Bushings and wear rings are the largest group, where a close bore and a known wall keep the part concentric in service. Insulators and spacers in electrical work use tube for the same reason, plus the wall thickness that sets creep resistance under a clamping load. Sight glasses and flow tubes need a transparent or translucent grade, and here the wall has to be uniform if optical distortion matters. Shafts and rollers that do not need a solid core are another common use. In each case the question is the same: which dimensions does the function care about, and which can be left at mill tolerance? All of these come from the same stock shape range.

Questions buyers ask about tube and hollow bar sizing

What is the difference between tube and hollow bar?

Both have a bore. Tube is usually produced by extrusion with a more consistent wall, while hollow bar is a thicker-walled form, often cast or compression moulded, with a smaller bore and more material around it. The naming varies between suppliers, so describe the outside diameter, inside diameter and length rather than relying on the label.

What wall thickness tolerance can I expect in plastic tube?

For extruded engineering plastics, a wall tolerance of roughly plus or minus five per cent is a realistic starting point, with ovality and concentricity of a similar order. Tighter than that usually means machining the bore after extrusion. Always quote the wall and not only the outside diameter, because the outside can be on size while the wall is not.

Is it cheaper to buy tube or bore solid rod?

It depends on the grade and the run length. Tube removes less material, so it wins on cycle time and swarf, especially in PEEK and PTFE. For a short run, or where you need full control of the bore, boring from rod can be cheaper overall because you avoid a cleanup cut and the risk of a tube that will not true up.

Which plastics are available as tube?

PTFE, PVDF, PEEK, PPS, POM and PA66 are all commonly available as tube. Filled grades and very thin walls are less predictable, so check stock before designing around them. Where a grade is not made as tube, a thick-wall hollow bar or a part machined from rod is the usual fallback, and the contact page is the fastest way to confirm what is on the shelf.

Нужна рекомендация по материалу?

Пришлите задачу — и мы ответим двумя-тремя подходящими марками и ценой.

Спросить инженера
Поделиться статьёй

Пришлите чертёж — получите цену за 24 часа

Назовите материал, размер и количество штук. Если не уверены в материале — опишите задачу, и мы его подберём.

Запросить цену Смотреть складские заготовки